CONTENTS

The PowerTrip Premium Travel Set contains the following units:
• 2,200mAh Power Bank
• Car Charger
• Travel Adaptor with interchangeable plug pins
• Multi-Link Cable


SPECIFICATIONS

Packaging: Luxury branded gift box
Packaging Size: 170x120x60mm
Commodity Code: 8504409990
Automatic Short Circuit and Surge Protection Built-In, Keeping You Safe.

SPECIFICATIONS

Capacity: 2,200mAh
Battery Type: A-Grade Lithium-ion
Circuit Board: A-Grade
Input: 5V ≤ 1,000 mA
Output: 5V ≤ 1,000 mA
Recharge Time: Approximately 2-3 hours
Discharge Time: Approximately 3-4 hours
Life Cycles: 500+
Unit Size: 95x24x22mm
Finish: Matt finish
Commodity Code: 8504409990
Automatic Short Circuit and Surge Protection Built-In, Keeping You Safe.
Red/Blue light to signal charging/recharging.


USAGE GUIDE

Step 1 | Charging Your Unit: Using the provided Micro-USB cable, plug the unit into a USB port capable of charging. The unit's light will turn on to signify that it is now charging. It takes approximately 3-4 hours to fully charge. Once fully charged, the light on the unit will turn off.

Step 2 | Connecting Your Unit To A Mobile Device: When your device needs charging, connect the unit using our supplied universal cable or your device's original USB charging cable. The unit's light will turn on to signify it is charging your device. It takes approximately 1-2 hours to fully charge your device. Once the unit has transferred all of it's power, the light on the unit will turn off.


TROUBLESHOOTING GUIDE

Problems Charging The Unit

If the light doesn't turn on after plugging it in...
• Make sure the unit is not already fully charged by connecting it to a mobile device. If it lights up, it already has power.
• Make sure you have connected to the 'Micro-USB input' of the device and not the 'USB output'.
• Make sure the USB output of your computer or other device supports charging, some USB ports, particularly on older devices, do not output power and therefore can not charge the unit. Try charging from a different device.
• Make sure you are using the provided Micro-USB charging cabled. If the unit is not charging using this cable, try an alternative cable to discover if this is the problem.
• If you are not using the provided charging cable, make sure the cable you are using supports charging, some Micro-USB cabled supplied with mobile phones or other devices will only charge particular devices.

Problems Charging Your Mobile Device With The Unit

If the light doesn't turn on after plugging the unit into the device...
• The unit may have entered short-circuit protection mode. This can happen when you are using a faulty cable or the wiring of the cable is not compatible with your mobile device. As a safety feature the unit will shut down to avoid damaging the mobile device. To reset the unit, plug it back in to charge using the provided Micro-USB cable and retry charging your device with a different cable that is compatible with your device.
• Make sure your mobile device is not already fully charged. Fully charged devices may cause the unit's light to flicker.
• Please check the cable you are trying to use is capable of charging by testing it with another device or unit. Some cables, particularly those provided with older devices may be data-only cables.
• Older mobile devices may support the connection but not accept charging via USB. Check the manual of the device you are trying to charge to see if your device is compatible.

The unit is fully charged and lights up when connected to my device, but nothing happens...
• A small percentage of mobile devices are wired to be incompatible with universal cables. If this is the case, try your device's original charging cable or seek assistance about compatible cables from the device's manufacturer.
• The majority of iPhones, iPods and iPads will charge with the universal cable, however, we are aware that some customers with a particular OSX, firmware version, or handset have experienced problems when using third party charging cables. If this happens please use your own original Apple charging cable.

MISCELLANEOUS PROBLEMS

The Unit Is Getting Hot.
This is a perfectly normal feature of all batteries when in use. But don't worry our unit is made from Lithium-Polymer, one of the safest, heat-resistant batteries on the market.

The Light On The Unit Is Flickering When Charging.
Some devices use a charging method which pulses energy into the device. This causes a flickering effect on the unit and is perfectly normal.

The Light On The Unit Flickers And Stops Charging When I Move The Device Or Unit.
Our provided cables are of extremely high quality, please check the cable connection incase of a loose cable. Or try replacing the cable.
If the replacement cable does not solve the problem, contact the supplying company to see if a return option is available.

The Unit Only Charged The Device For A Short Time And The Light Turned Off.
This rarely happens and it is not normal unless the Unit was only partially charged.
There is a possibility the charging of the Unit was interrupted, this can happen on devices that turn off power output on their USB ports when entering standby mode or if it is not actively in use in order to save power.
If this happens try recharging the unit from a stable USB power source and ensure it does not enter sleep or standby mode.
The unit should normally take 2-5 hours to fully charge, if this doesn't happen, please try recharging the unit from an alternative source.

SPECIFICATIONS

Circuit Board: A-Grade
Input: 12V/24V via Car Socket
Output: 5V ≤ 1,000 mA
Unit Size: 85x25x22mm (at largest points excluding tip)
Finish: Matt finish
Commodity Code: 8504409990
Automatic Short Circuit and Surge Protection Built-In, Keeping You Safe.


TROUBLESHOOTING GUIDE

Problems Connecting The Unit

If the light doesn't turn on after plugging it in...
• On the rare occasion, your car cigarette lighter socket may be too deep for the unit to reach and is unfortunately incompatible. Please use in different cigarette lighter socket if available or purchase a socket adaptor.
• Turn the unit inside the socket to check if there is a loose connection in the socket.

Problems Charging Your Mobile Device With The Unit

If the device does not indicate it is charging/receiving power when plugged in...
• The unit may have entered short-circuit protection mode. This can happen when you are using a faulty cable, the wiring of the cable is not compatible with your mobile device, or there is a surge from the car. As a safety feature the unit will shut down to avoid damaging the mobile device. To reset the unit, plug it back into the cigarette lighter socket and then retry charging. If the problem persists retry charging your mobile device with a different charging cable which is known to work correctly.
• Make sure your mobile device is not already fully charged. Fully charged devices may cause the unit's light to flicker.
• Please check the cable you are trying to charge with by testing it on another unit. Some cables provided with older handsets may be 'data only' cables and not support charging.
• Older mobile phones and digital cameras, although support the connectors we provide, may not accept charging via USB. Please check the manual or contact the device's company to check if your device is compatible.

If the unit is plugged in, the device is connected and the light is on but nothing happens...
• A small percentage of mobile devices are wired to be incompatible with universal cables. If this is the case, try your device's original charging cable or seek assistance about compatible cables from the device's manufacturer.
• The majority of iPhones, iPods and iPads will charge with the universal cable, however, we are aware that some customers with a particular OSX, firmware version, or handset have experienced problems when using third party charging cables. If this happens please use your own original Apple charging cable.

MISCELLANEOUS PROBLEMS

The Unit Is Getting Hot.
This is a perfectly normal feature of charging electronics when in use. Expect the Unit to get pretty hot! But don't worry, our unit is extremely heat resistant!

The Light On The Unit Is Flickering When Charging.
Some devices use a charging method which pulses energy into the device. This causes a flickering effect on the unit and is perfectly normal.

The Light On The Unit Flickers And Charging Stops And Starts When I Move The Unit
Please check the car charging socket has a firm connection to the Unit as this likely the problem.
Our provided cables are of extremely high quality, but please check the cable connection. If there is a loose cable, please use your mobile device's provided charging cable or look to purchase a replacement.

SPECIFICATIONS

Circuit Board: A-Grade
Input: 110-240V
Output: 5V ≤ 1,000 mA
Unit Size: 49x28x22mm
Tip Sizes: 31x24x23mm (UK, excluding wings), 31x24x23mm (Europe), 31x24x23mm (Australia)
Finish: Matt finish
Commodity Code: 8504409990
Automatic Short Circuit and Surge Protection Built-In, Keeping You Safe.


USAGE GUIDE

Step 1 | Plugging In The Unit: Plug the unit into a wall socket. Interchangeable plug pins are included to make the Travel Adaptor compatible anywhere in the world.

Step 2 | Connecting Your Unit To A Mobile Device: When your device needs charging, connect the unit using our supplied universal cable or your device's original USB charging cable. The device should automatically start charging.


TROUBLESHOOTING GUIDE

Problems Charging Your Mobile Device With The Unit

If the device does not indicate it is charging/receiving power when plugged in...
• The unit may have entered short-circuit protection mode. This can happen when you are using a faulty cable, the wiring of the cable is not compatible with your mobile device, or there is a surge from the socket. As a safety feature the adaptor will shut down to avoid damaging the mobile device. To reset the adaptor, unplug it and plug back in, then retry charging. If the problem persists retry charging your mobile device with a different charging cable which is known to work correctly.
• Make sure your mobile device is not already fully charged.
• Please check the cable you are trying to charge with by testing it on another unit. Some cables provided with older handsets may be 'data only' cables and not support charging.
• Older mobile phones and digital cameras, although support the connectors we provide, may not accept charging via USB. Please check the manual or contact the device's company to check if your device is compatible.
• A small percentage of mobile devices are wired to be incompatible with universal cables. If this is the case, try your device's original charging cable or seek assistance about compatible cables from the device's manufacturer.
• The majority of iPhones, iPods and iPads will charge with the universal cable, however, we are aware that some customers with a particular OSX, firmware version, or handset have experienced problems when using third party charging cables. If this happens please use your own original Apple charging cable.

MISCELLANEOUS PROBLEMS

The Unit Is Getting Hot.
This is a perfectly normal feature of charging electronics when in use. Expect the Unit to get pretty hot! But don't worry, our unit is extremely heat resistant!

SPECIFICATIONS

Circuit Board: A-Grade
Connectors: iPhone 5/6 Lightning cable, iPhone 4 30-Pin cable, Micro-USB cable & USB cable
Input: Device dependant
Output: 5V ≤ 1,000 mA
Unit Size: 45x25x12mm
Cable Lengths: 70mm
Finish: Matt finish
Commodity Code: 8504409990


USAGE GUIDE

Step 1 | Connecting Your Unit: Plug the unit into a computer USB port capable of charging via USB. The computer may not detect the Link and instead only detect the devices plugged into the unit's USB ports.

Step 2 | Connecting A Power Source: When connecting a mobile device into a connected Link, your device should begin to charge.


TROUBLESHOOTING GUIDE

Problems Charging Your Mobile Device Using The Unit

If the unit plugged into a power source and the connected mobile device does not charge ...
• The unit may have entered short-circuit protection mode. This can happen when you are using a faulty cable or the wiring of the cable is not compatible with your mobile device. As a safety feature the unit will shut down to avoid damaging the mobile device. To retry, plug the Link back in to the mobile device and power source, or try using a different power source.
• Make sure your mobile device is not already fully charged.
• Older mobile devices may support the connection but not accept charging via USB. Check the manual of the device you are trying to charge to see if your device is compatible.
• A small percentage of mobile devices are wired to be incompatible with universal cables, and are therefore incompatible with the PowerLink.
• The majority of iPhones, iPods and iPads will charge with the PowerLink, however, we are aware that some customers with a particular OSX, firmware version, or handset have experienced problems when using third party charging cables. In these rare cases, the PowerLink is not compatible

MISCELLANEOUS PROBLEMS

The Unit Is Getting Hot.
This is a perfectly normal feature of charging electronics when in use. Expect the Unit to get pretty hot! But don't worry, our unit is extremely heat resistant!

The Device Charges For A Short Time And Then Stops.
There is a possibility the connection between devices was interrupted, this can happen on devices that turn off power output on their USB ports when entering standby mode or if it is not actively in use in order to save power.
If this happens try connecting the unit to a stable USB power source and ensure it does not enter sleep or standby mode.

BRANDING

Packaging: Luxury Gift Box with Resin Dome Decal
Type: Resin Dome Decal
Decal Size: 43.5x22.5mm - with 2mm radius corners
Colours: Black or White
Pantone matching available free of charge on orders of 250 units or above.

WARRANTY DISCLAIMER

All products are generally guaranteed to be free from defects within 1 year after delivery to your supplier. This means although 1 year warranty is offered on your unit, you will need to contact your supplier for the exact warranty date. Due to these procedures we generally offer an extra month on the warranty to account for possible delays in the unit reaching the end user.

The unit is covered for any defects within this warranty period with the exception of general wear and tear caused by frequent use.

We will cover any defect in the LED or LID systems due to wiring faults, soldering faults or casing deformations. If an international short circuit or intentional malicious damage is found the unit is not covered under warranty.

Units that have been opened by any part or accidently damaged by any users or suppliers are not covered.